Menu
Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Search
Search titles only
By:
Search titles only
By:
New posts
Search forums
Search
Search titles only
By:
Search titles only
By:
Menu
Welcome DJI Spark Pilot!
Jump in and join our free Spark community today!
Sign up
Forums
DJI Spark Forums
Spark Discussions
Couldn't Start Firmware Update: Spark & Remote Wouldn't Connect to Go 4 App...Worked Yesterday
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Continuous Lift" data-source="post: 123234" data-attributes="member: 23347"><p>Yesterday I was able to connect my spark, remote, and iPhone 12 using the OTG cable and was ready to update firmware...Go 4 app showed 'Connected' and orange banner showed updates to be installed. Today I wanted to <u>actually</u> update firmware but only the drone and remote would connect. The two wouldn't connect to the Go 4 app.</p><p></p><p>So I restarted iPhone, changed OTG cables, deleted and reloaded Go 4 app, and resigned into Go 4 app. App showed my assigned Spark name 'Gordo2'...so I was signed in.</p><p></p><p><strong>Can anyone spot anything I did wrong with the procedure below? </strong></p><p><strong>Procedure:</strong></p><p>1) Turned on remote</p><p>2) Turned on Spark</p><p>3) Opened up Go 4 app, selected Spark from drone list, was signed in as mentioned above.</p><p>4) Connected iPhone and remote with new OTG cable.</p><p>5) Pushed and held battery button for 3 seconds & drone emitted single beep. (Page 38, manual)</p><p>6) Remote: Held down 3 buttons: Pause + FN + Custom buttons simultaneously (Page 38 manual)...beeping and flashing LEDs on drone...controller, red light flashing, and then connection...Beeping stopped and </p><p> solid green light on remote...could start up motors with remote.</p><p></p><p><strong>But... Go 4 app still said, 'Not Connected'.</strong></p><p><strong></strong></p><p><strong>Any suggestions?</strong></p></blockquote><p></p>
[QUOTE="Continuous Lift, post: 123234, member: 23347"] Yesterday I was able to connect my spark, remote, and iPhone 12 using the OTG cable and was ready to update firmware...Go 4 app showed 'Connected' and orange banner showed updates to be installed. Today I wanted to [U]actually[/U] update firmware but only the drone and remote would connect. The two wouldn't connect to the Go 4 app. So I restarted iPhone, changed OTG cables, deleted and reloaded Go 4 app, and resigned into Go 4 app. App showed my assigned Spark name 'Gordo2'...so I was signed in. [B]Can anyone spot anything I did wrong with the procedure below? Procedure:[/B] 1) Turned on remote 2) Turned on Spark 3) Opened up Go 4 app, selected Spark from drone list, was signed in as mentioned above. 4) Connected iPhone and remote with new OTG cable. 5) Pushed and held battery button for 3 seconds & drone emitted single beep. (Page 38, manual) 6) Remote: Held down 3 buttons: Pause + FN + Custom buttons simultaneously (Page 38 manual)...beeping and flashing LEDs on drone...controller, red light flashing, and then connection...Beeping stopped and solid green light on remote...could start up motors with remote. [B]But... Go 4 app still said, 'Not Connected'. Any suggestions?[/B] [/QUOTE]
Verification
Post reply
Forums
DJI Spark Forums
Spark Discussions
Couldn't Start Firmware Update: Spark & Remote Wouldn't Connect to Go 4 App...Worked Yesterday