New user setup question

[Kevin Kirby]

I just unpacked my Spark with RC, and have read I can control the drone without a phone. The are paired, and I can take pictures and control the gimble with the thumb wheel, but I can't seem to take off. I have tried pulling both sticks to bottom inside, as well as bottom outside, and the unit does nothing.
I have not registered or created an account, do you think this would result in all functions working except flight?

 

[idbl_fanatic]

You won't be about to tell if you have gps lock and might have a fly away

 

[DesertWindAero]

I have not registered or created an account, do you think this would result in all functions working except flight?

More than likely.

 

[Kevin Kirby]

I see that now. This forum is very helpful. So I've downloaded the app, but can't get the vehicle registered. I've tried scanning the QR code but get an error. I've connected to it via Wi-Fi, but it fails to recognize that in the registration phase. This is so frustrating!

 

[DesertWindAero]

I see that now. This forum is very helpful. So I've downloaded the app, but can't get the vehicle registered. I've tried scanning the QR code but get an error. I've connected to it via Wi-Fi, but it fails to recognize that in the registration phase. This is so frustrating!

Have you checked the DJI website for assistance? YouTube?

 

[Canso]

Power up the controller then the spark, controller light will go from red to green when the spark has conected to the controller. You may have to “pair” the controller to the spark if you bought separate.
Then use your phone to connect to the controller wifi ssid located on the bottom of the controller, type it in don’t scan.

 

[Lastrexking]

Don’t use the QR code. Type the details in.

 

[Kevin Kirby]

Power up the controller then the spark, controller light will go from red to green when the spark has conected to the controller. You may have to “pair” the controller to the spark if you bought separate.
Then use your phone to connect to the controller wifi ssid located on the bottom of the controller, type it in don’t scan.

I don't see any textbox to type the QR code on the app. Its the DJI GO 4, and my options are Activate Aircraft, Connect to Aircraft, and Enter Camera View. The first is the QR code reader only. The second allows me to connect to the drone vs drone with RC, via Wi-Fi. There is also an option to scan the QR code there. Third, enters the GUI, but lists the unit as disconnected. Where do I type in the QR code.
Thank you for your help.

 

[msinger]

Try activating your Spark like this:

To view this content we will need your consent to set third party cookies.
For more detailed information, see our cookies page.

Accept third party cookies

 

[Kevin Kirby]

I am still not able to get this darn thing to work with the app on my phone. I was able to get it to work on my iPad however, so I have been flying it in the house (and outside in the backyard). My question is, can anyone tell me why it won't use the GPS? It will show that it has 8 or 9 satellites, but still says "no GPS".

 

[Kevin Kirby]

I am still not able to get this darn thing to work with the app on my phone. I was able to get it to work on my iPad however, so I have been flying it in the house (and outside in the backyard). My question is, can anyone tell me why it won't use the GPS? It will show that it has 8 or 9 satellites, but still says "no GPS".

Here is a pic showing it found satellites.

 

[Spark 317]

The Spark will fly in Atti mode while inside the house as it is difficult to receive the GPS signal due to your roof blocking the signal.

GPS is a weak signal from satellites in orbit around the Earth.

A GPS receiver such as the Spark can lose a GPS signal while in cities with tall buildings, deep in valleys, or in dense woods.

While you may get some satellite coverage indoors it may not be enough information for flight in three dimensions.

 

[Kevin Kirby]

Thank you.